Jump to content
Security Installer Community

MrHappy

Global Moderator
  • Posts

    17,738
  • Joined

  • Last visited

  • Days Won

    706

Everything posted by MrHappy

  1. at 3k a ton the old copper pipe is worth more than the alarm
  2. I tend to butcher plastics & pcbs when removing Friday night I changed a 9 circuit Euro 12 c/w old metal zem into 76M that I had on stock. I unscrewed the speaker, scb & rkp then chopped the euro 12 pcb in half, hacked away at the plastics & until the pcb would pass out the back of the old cabinet, removed old zem from metal cabinet & mounted pcb into new endstation. 1.5hrs on site, everything texted up & tested.... however new cabinet did look a bit pissed on the wall when I stood back to admire it.
  3. most panel manufacturer list printer interfaces, bet they sell less than they are churches saudi I think this is the same as my datac printer? https://www.checkline.eu/products/126322/large/126322.jpg
  4. I've never seen an opus 42 or cpa6 I acquired datac printer from scantronic multiscan, In my experience a branch of national co. or large regional installer might have one 7300 nvm programmer or a logging printer
  5. Around here 860k for 5 ded detached town house is alot of money, She'd wanted some new sockets in the kitchen & the electrics have been condemned, 2 core in conduit under the kitchen floor nothing earthed, Told its 200k project of tarting the place up, plaster chopped off down stairs floors being replace up stairs, not sure whether she want the cctv (project manager has instructed me to wire regardless) alarm is part rewired, galaxy 16 is likely to be replaced if she wants a RKP with a fancy finsh... ceiling mounted access points, a few speakers & some cables have appeared... told 10k charged for the work (3 days labour)
  6. There's lots of different prox tokens It would appear using ones of the incorrect format screw up the existing ones ?
  7. TSI list is anyone who wants to be listed on it, A better list to work from on - http://www.nsi.org.uk/ or https://ssaib.org/ however they'll want a margin on the gear, a mans wages & probably a maintenance contract too
  8. Should have signed yourself up as "approved" whilst on the line,
  9. a paid adverts Texecom approved/ registered means fuck all, I could get my goldfish signed up... we'd be above £60 for for visit, TBH most of the site is petty piss taking ? Buy metal cased premier, 7ah is okay depending how much kit is powered of it
  10. oh dear.... commiserations & welcome to TSI
  11. just found with images, buy from here https://www.oldskoolhooligans.com/bus-wankers-t-shirt-inspired-by-the-inbetweeners-12622.html
  12. I reckon I could sort this system in under an 1hr, should the device report a low battery with the next 28 days I'return & just charge for the device I have old types & new on the shelf. The other topic with Everest abacus, again sorted within an 1hr, Both could have fully comp contracts, however I probably start with wanting money for bells & batterys to put money in the pot
  13. alarms ain't consumer devices, their niche market low volume & expensive for old tech the same doors contacts are still being sold, only the very early one are unavailable as they changed the mhz ? ring risco & ask who'd they recommend locally
  14. I once pulled an electronics line wirefree system that had a "ts900" keypad on it, normally they had "napco" type keypad I often regret not trying it on ts networker to see if it would work
  15. aviva, they're a set of pricks. However they did have to pay out 30k+
  16. printer port, molex pins for pc on rhs of pcb nr battery appears to have everest software & rkp plastic from HKC ? IIRC udl worked with 6/14 but not the radio version ?
  17. basic maintenance would be a visit & access to "service on demand" that so pricks can ring up at 4am to tell them the alarm has gone off, oddly most employees expect to paid to make themselves available & sober to go & repair alarms at the drop of a hat, you'd probably be charged for any parts & any extra visits so co's do fully comprehensive you pay your money & makes your choice
  18. The pricks that ring me up in the middle of the night just to wake me because their awake are the same sort of pricks that don't release I've got loads of system that can make timed test calls, or just might ring them back the following week at 4am to check the system is doing okay...
  19. w/o a maintenance contract its not like your paying him any income to be woken up at 4am, what do you expect?
  20. Its a security system... it sold as conforming to std part of that std requires anti tamper circuits, if your the sort of person that lives alone, has no friends or guests visiting, never has any tradesmen ect in the house then the anti tamper feature on the sensor can easily be removed using a soldering to blob out the the switch on the pcb If you have co. which does not maintain systems & sells the engineering code..... err I think you may be dealing with "S Hit Alarms Ltd;"
  21. no, after using the old abacus radio system we moved to Risco (2005ish) ... I'd charge for corrective visit & a new pir (if its very early system it may be old pcb in new case) I'd then offer you basic or fully comp maintenance, Like the radio abacus topic of the other day the equipment is stable but quirky a competent engineer with suitable experience of the product & its piece of piss
  22. I can seen a system we installed in 1990 on the database, it started with a 9800 then later updated to ts690 I think the 9800 may go back to 1988/89 ? We once had white a4 manuals in the store rather then the later grey shiney a5 one...
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.