Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,332

  • Joined

  • Last visited

  • Days Won

    124

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Lol You ever worked on bt network?
  2. al-yeti
    Thought bt providing pstn through the fibre box Total blag of a title , "The decent alarm panel you installed like ..... Will work on another path no problem by a simple upgrade " Years away from dropping pstn
  3. al-yeti
    So these have a little screw holding board in I think, you could take pic, remove 12v tape up and in turn each one tape up separately Then take board out only and swap over with other Some might say upgrade the pirs anyway and scrap it ......
  4. al-yeti
    What pirs are they, picture? If it's possible you could remove the power tape them up and then swap boards over etc
  5. al-yeti
    Yes , you don't have to use engineer hold off though , be careful with the power connections tape them to be safe and take a picture of how it was wired
  6. al-yeti

    Hello

    al-yeti replied to KWCFC's topic in Introduce Yourself

  7. al-yeti

    Hello

    al-yeti replied to KWCFC's topic in Introduce Yourself

    Remember the film "Falling Down"
  8. al-yeti

    Hello

    al-yeti replied to KWCFC's topic in Introduce Yourself

    You will be assimilated of course
  9. al-yeti
    Is this new ?
  10. al-yeti
    You have two power supplies? One for cameras one for recorder? What do you mean lost all night vision? Do you mean you had day pictures but no pictures at night? Maybe power supply being overloaded when ir lamps come on , so possibly power fault
  11. al-yeti
    As the bods here taught me both have there uses , 24vac can be used further
  12. al-yeti
    All nonsense , except you need it on very few sites
  13. al-yeti
    I would say if you have time make a note of how it's wired, written and pictures Then wire up front bell as a single unit and try and get it to work Or if you really think it's front battery , change it, it's cheap And as above can you do this right...
  14. al-yeti
    No detection in garage, means you can get to it without starting try tomorrow or full alarm
  15. al-yeti
    Maybe there way of doing the tampers ?
  16. al-yeti
    Diy stick both detectors on one zone and lash it in
  17. al-yeti
    Serious you can't make two zones entry?
  18. al-yeti
    Do you have engineer code? Do you have installation manual? Does the walk route from zone 3 go via any other zones apart from zone 1 ?
  19. al-yeti
    Hmm I think I got mine in around 1995 or so aswell with an rs stamp on it Ok like the new tacwise though
  20. al-yeti
    Model no and pictures of detector?
  21. al-yeti
    So it's ok then?
  22. al-yeti
    0.8v where? Cable fault? Do they share a cable?
  23. al-yeti
    Not yet, but they just got hunters in Slough to start selling the hkc gear it's on there website for trade only no pricing Problem around this area is the £300 brigade will buy it and sell onto the public, total lunatics working for a cheap day rate Maybe just maybe, if they sell enough to trade they won't go with Joe public
  24. al-yeti
    Getting to end solution
  25. al-yeti
    You could in such and old system add a remote if the facility or local engineer is able to do it , if it has a key switch , with a few circuits added on
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept