Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,332

  • Joined

  • Last visited

  • Days Won

    124

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Because it normally starts positive and by the end of a tsi thread it's negative , kind of adds up this
  2. al-yeti
    What equipment is it? Components work fine in very warm areas , probably more prone to failure in a loft where temp changes more often , but depends on build quality Of course this could all be blag
  3. al-yeti
    I wasn't talking about the triggers, so it should work, how will you monitor external psu ? Perhaps 12v relays connected to zones in panel so you know when there's a fault
  4. al-yeti
    Setting bells like that depends also on system output , current draw of bells and current output of panel Current draw when bells are both going nuts and pulls the panel down because panel output wasn't strong enough You get it
  5. al-yeti
    Better to set one bell to scb mode and second to sab , or whichever way round, As for resistor dont know the panel well but it's probably requires otherwise will keep showing bell tamper , resistor that comes with delta bell is explained in instructions And yes depending on panel you can use an output to control engineer hold off , but I don't I just know which leg it is and apply if and when required manually, on the delta that is
  6. al-yeti
    as petrol says wrong ones and you cut frequencies that you need
  7. al-yeti
    Reading up in technomate seems this unit must be connected to a DVB compatible TV , so hope that's what your doing as it's a hd convertor Standard ones will do straight to the normal TV channels if that makes sense which don't require hd compatibility
  8. al-yeti
    If you can't get pictures out if the HDMI convertor no point trying any further Havnt done this in a long time but channels were normally between 21 Upto 33 stay clear of , higher channels should all work Are you auto tuning , do manual slow tuning set on high channel directly connected to the convertor output What's model number and name if not a technomate
  9. al-yeti
    You need to do this stage by stage remove aerial etc and start with Cctv direct and take it step by step I assume out of the HDMI convertor if you put a TV right next to it and plug it in direct you can get a picture?
  10. al-yeti
    Can you get a picture direct out if the HDMI convertor?
  11. al-yeti
    I know I said catch fire , but y you wanna torch it? Should be in messed up joke section
  12. al-yeti
    Judging by the small holes etc he's read one of your gashing posts Although I wonder how long it will be before that battery catches fire , lead acid battery in an alarm panel???? Or drilled into a gel one , hardcore
  13. al-yeti
    Galaxy will cope well if you know the panel and setting up groups, but I wouldn't use a flex , dimension would work better , unless they already debating on price, never used the access side on dimension not sure if it's compatible Pete might be able to programme something on cards And there are experts here on galaxy who will tell you how to integrate , groups bit striaght forward However hkc is much easier on software side......
  14. al-yeti
    How are the tamper terminals wired in then ?
  15. al-yeti
    You have a prox keypad?
  16. al-yeti
    Well you could leave in installer.mode , disconnect keypad wires in panel and go replace.keypad Or some here would just swap it over live , depends on how brave you feel Or "happ"ily drill through wall and reach for keypad through hole for fun of it and have filla ready
  17. al-yeti
    A b c and D are all different setting programmes , you will find exit tone is different when pressing one of those to set
  18. al-yeti
    Spider with conductive legs across 0v and strobe is what mrH meant
  19. al-yeti
    So does galaxy ie line and engineer reset, only problem with galaxy to easy to take over, maybe back to the 9651 for training purposes with a prox keypad
  20. al-yeti
    It can work with another path though I thought , that goes with any app based system take the broadband out and your stuffed
  21. al-yeti
    Texecom
  22. al-yeti
    Free apps is all the rage though and pstn is rubbish compared to free apps Haha
  23. al-yeti
    Visonic powermax have lots of wired options available, why don't you just experiment with one of those , then dump visonic altogether Or get an easy grade one cheap old tat that you don't mind setting on fire , keep fire extinguisher handy incase you bridge fuses with foil paper
  24. al-yeti
    What's his best option as a striaght swap
  25. al-yeti
    Was it chirping because it was bent?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept