Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,627

  • Joined

  • Last visited

  • Days Won

    141

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Here's the simple answer which you didn't accept , as that would been the end of that, hence what continued perhaps Here's another great reply , but in English it says it's easy to get these over the web, plus you still have a code as fail safe What more do you want It is in English dd but he needs help
  2. al-yeti
    Change the battery anyway
  3. al-yeti
    Why don't you do basic electronics course first? It will teach you this stuff Then house bash dot com
  4. al-yeti
    You gprs works out there ?
  5. al-yeti
    Open tap is expensive , I wouldn't want every signal being sent
  6. al-yeti
    Yes this does occur with other diallers and many handsets and then it suddenly starts working on next call
  7. al-yeti
    Wireless or wired
  8. al-yeti
    Yes there rf range is very poor with to many objects in the way if you get me
  9. al-yeti
    Engineer mode won't help you with short circuits , and as above you can do serial as said with last one being terminated , and also do star config You will have ti make sure you address everything carefully , big house ? To rf portals?
  10. al-yeti
    As above , but you can star it no problem and put a resistor on at "each" end of line If you blew a fuse you must have shorted something not because of an overload , the connections on the g2 can be tricky for some ,xso look carefully when your doing it and power down if possible , your bell may go nuts while doing it of course
  11. al-yeti
    None of them are straight forward , if your sticking to wired then galaxy may work for you , is it a commercial? Have you looked at texecom? Euro mini?
  12. al-yeti
    Young reader want to convert it to emp
  13. al-yeti
    Nah , for commercial maybe, but residential other panels are moving ahead , honeywell should sell up and end up like Eaton bosch who also don't do jack to develop there products
  14. al-yeti
    Yes take cover off , hope it's not engineer reset or something crazy
  15. al-yeti
    All down to risk assessment then?
  16. al-yeti
    So your back to square one, first determine if they work independently Then it can only be a cable fault or wiring problem Maybe you are connected something wrong and didn't notice , as a house bashers I do it often , still good to fry the stuff now and then
  17. al-yeti
    Ok so your saying individually they both work fine, flash strobe trigger bell all ok? , if that's the case then it's wiring or cable fault Not sure if these have a resistor to be used ? Is it fed from front to rear or rear to front , replace cable through loft if that's the shorter one , Are you using 8core or struggling with 6 and no other spares
  18. al-yeti
    Can you wire up the bell that isn't working in its own, if so does it work?
  19. al-yeti
    Because it normally starts positive and by the end of a tsi thread it's negative , kind of adds up this
  20. al-yeti
    What equipment is it? Components work fine in very warm areas , probably more prone to failure in a loft where temp changes more often , but depends on build quality Of course this could all be blag
  21. al-yeti
    I wasn't talking about the triggers, so it should work, how will you monitor external psu ? Perhaps 12v relays connected to zones in panel so you know when there's a fault
  22. al-yeti
    Setting bells like that depends also on system output , current draw of bells and current output of panel Current draw when bells are both going nuts and pulls the panel down because panel output wasn't strong enough You get it
  23. al-yeti
    Better to set one bell to scb mode and second to sab , or whichever way round, As for resistor dont know the panel well but it's probably requires otherwise will keep showing bell tamper , resistor that comes with delta bell is explained in instructions And yes depending on panel you can use an output to control engineer hold off , but I don't I just know which leg it is and apply if and when required manually, on the delta that is
  24. al-yeti
    as petrol says wrong ones and you cut frequencies that you need
  25. al-yeti
    Reading up in technomate seems this unit must be connected to a DVB compatible TV , so hope that's what your doing as it's a hd convertor Standard ones will do straight to the normal TV channels if that makes sense which don't require hd compatibility
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept