al-yeti

Ok I get you So upto 800m no device in-between?

Ok but nothing others can't do right ?

With the risk of making them into bricks , just find the hikvision model and firmware and try it If it works then fine other you can use as paper weights for desk

There's nothing special your showing here with repeaters and coax lol

No good for the enforcer as it doesn't have scb mode , get a better bell for extra tenner Apart from that look at zone and bell on manual and your done

Members are very helpful for people who want everything free , in there own time , waiting for op to do something and say what the errors are Remember you could be anyone trying to compromise someone else's system, it's a shame so many are to helpful in my.opinion Happy reprogramming

How much it costs to flash? Just wondering you got help to flash but no one can help to default But never mind atleast you got it to work and your insurers can have a laugh , Sweden regs must be strange , but on other hand sounds like what the world will be doing when mostly DIY products take over

He deals in gold , poor human Atleast we know the subs in Sweden are just bad as in UK

The speech dialler has a Negative Positive Trigger Phone connections As a basic Negative to negative Positive to 12v+ aux Trigger can connect to the bell trigger which you may need to setup on the v2tel side after Phone connections to 2&5 of your extension socket , not the master side will be easiest for you Although if you got opportunity to return the dialler and get a GSM version you maybe better off future wise

Yes £350 expensive But I never said goto the original installer Lol flash away

Have you tried updating your firmware and then doing a cold start , and so on Seems like allot of hassle on texe equipment or you need to update the smart com Uninstall smartcom , reinstall , update firmware Just guessing for you untill someone like swb can help perhaps

Need texecon firmware experts

Lol n1

Forum rules mean I can't I am afraid , I signed up to it , so it's in the blood , the tsi clergy will send the Boyz round from hull , they don't fight fair either Anyhow back to reality Any reason you won't pay engineer small amount to do it for you?

Ok so think about it , if moving a sensor across clears the fault them you don't need to do much to put a resistor of correct value on 1002 to keep fault clear , even if it was a trailing wire with both resistors connected soldered This is all house bash moves as we say , ultimately you need engineer code It would be worthwhile calling a private engineer asking him to default the codes for you and then your done , that way some dust can come off your wallet and cobwebs can be removed from your stash , spider season is over

So if you move 1004 to 1002 does it clear 1002? If so you know what to do , get another PIR Or enter engineer mode (which your post was removed quite rightly earlier ) Default your codes which we can't help you with , but you weren't far off from getting it done , probably just read something wrong Then set 1002 as spare

Can't be 110 needs to be 1k I thought Unless your saying all the zones set up that way

You said your selling up , and handed most your stuff over ? I think your an imposter

What values are the resistors? As you used the tamper one to put on the panel All I am saying if you can't clear the fault with a simple resistance, then your eol must be set different to what your putting in and it doesn't matter what sensor or cable your using , all of no consequence What happens if you move a sensor from further up to zone two or three , it should clear the fault and send the fault to other Rio output

Another thing , show a picture of how one of your pirs is working , how is it wired and what resistors are inside it This will help you why your not able to clear the fault on z2& z3

In your picture above zone 3 shows the wiring sheath isn't removed and can be a problem , did you correct that?

Going to basics If your remove the wiring and put a resistor in the correct place it should clear any fault that is present there

Must mean zone 2 was being used as a sab tamper maybe? But earlier you said it was a PIR So when you say you get +sab and 1002 are you sure these are not separate faults and your not confusing matters

You got a picture of where you put resister?

Classis is me lol So enable in menu 48 , and then enter engineer code But OP more than likely you don't have it so try the resistor and then you might be lucky if it's all user reset