Jump to content
Security Installer Community

al-yeti

Trade Full Member
  • Posts

    9,332
  • Joined

  • Last visited

  • Days Won

    124

Everything posted by al-yeti

  1. al-yeti

    John G

    The speech dialler has a Negative Positive Trigger Phone connections As a basic Negative to negative Positive to 12v+ aux Trigger can connect to the bell trigger which you may need to setup on the v2tel side after Phone connections to 2&5 of your extension socket , not the master side will be easiest for you Although if you got opportunity to return the dialler and get a GSM version you maybe better off future wise
  2. Yes £350 expensive But I never said goto the original installer Lol flash away
  3. Have you tried updating your firmware and then doing a cold start , and so on Seems like allot of hassle on texe equipment or you need to update the smart com Uninstall smartcom , reinstall , update firmware Just guessing for you untill someone like swb can help perhaps
  4. Forum rules mean I can't I am afraid , I signed up to it , so it's in the blood , the tsi clergy will send the Boyz round from hull , they don't fight fair either Anyhow back to reality Any reason you won't pay engineer small amount to do it for you?
  5. Ok so think about it , if moving a sensor across clears the fault them you don't need to do much to put a resistor of correct value on 1002 to keep fault clear , even if it was a trailing wire with both resistors connected soldered This is all house bash moves as we say , ultimately you need engineer code It would be worthwhile calling a private engineer asking him to default the codes for you and then your done , that way some dust can come off your wallet and cobwebs can be removed from your stash , spider season is over
  6. So if you move 1004 to 1002 does it clear 1002? If so you know what to do , get another PIR Or enter engineer mode (which your post was removed quite rightly earlier ) Default your codes which we can't help you with , but you weren't far off from getting it done , probably just read something wrong Then set 1002 as spare
  7. Can't be 110 needs to be 1k I thought Unless your saying all the zones set up that way
  8. You said your selling up , and handed most your stuff over ? I think your an imposter
  9. What values are the resistors? As you used the tamper one to put on the panel All I am saying if you can't clear the fault with a simple resistance, then your eol must be set different to what your putting in and it doesn't matter what sensor or cable your using , all of no consequence What happens if you move a sensor from further up to zone two or three , it should clear the fault and send the fault to other Rio output
  10. Another thing , show a picture of how one of your pirs is working , how is it wired and what resistors are inside it This will help you why your not able to clear the fault on z2& z3
  11. In your picture above zone 3 shows the wiring sheath isn't removed and can be a problem , did you correct that?
  12. Going to basics If your remove the wiring and put a resistor in the correct place it should clear any fault that is present there
  13. Must mean zone 2 was being used as a sab tamper maybe? But earlier you said it was a PIR So when you say you get +sab and 1002 are you sure these are not separate faults and your not confusing matters
  14. You got a picture of where you put resister?
  15. Classis is me lol So enable in menu 48 , and then enter engineer code But OP more than likely you don't have it so try the resistor and then you might be lucky if it's all user reset
  16. Thought it has to be enabled ? While your stuck get a resistor and put it across 1k and it should stop it from throwing the error until you work something out
  17. Think he selected wrong forum , he discord is what he uses normally
  18. You using power Rio?
  19. SimpleGuy
  20. Not really Common for fan to make the noise If hard disk doesnt spin up common for hd failure rather than PSU All vague unless you test it all of course , you don't need logs and menus to test that stuff
  21. So it means setting b?
  22. This is UK , we don't read anything , especially manuals until we desperate
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.