Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,306

  • Joined

  • Last visited

  • Days Won

    120

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Silent on panic setting?
  2. al-yeti
    Why does Logan's name say guest?
  3. al-yeti
    Commissioning? Like second fix? Lash panel to wall Keypad Bellbox Detectors Programming Testing All via lazy laptop where possible Demo for customer , and go get some grub if they didn't give you any .....
  4. al-yeti
    Well there's loads of old parts marked adt on eBay so as long as your security is just a DIY thing ,and not protecting much of value to you , should be all good
  5. al-yeti
    If wiring correct There's a screw near tamper switch , or you saw it in packet and didn't put it in , that will help push switch if surface behind wasn't even You don't need to remove bell , just put screw in and turn it to adjust switch slightly and you will here the switch close quicker when cover is pressed down Assuming it's this , but it is normally the problem
  6. al-yeti
    Grade 2 easier to do than grade 3
  7. al-yeti
    Strangest comment so far .... But keep going
  8. al-yeti
    This bit most serious comment you have written and explains the job, so in this note carry on Good luck to someone who takes it over lol
  9. al-yeti
    Veritas will be difficult even the electrician's can't do them fully Start with Honeywell g4 - 9651 - galaxy g2-12 - then dive into a dimension on left hand and premier elite in right at same time
  10. al-yeti
    I do a bit , hate the bell boxes high up never understood why they do that , bunch of nuttas and muppets
  11. al-yeti
    Nah, this means you can probably fault find , so qualified.....
  12. al-yeti
    If you don't use it, a d don't think you need security , switch it all off end of story I assume you didn't have it installed and was already there , cats or no cats alarms can work with pets if make adjustments All depends on how much you want to spend on it and wether you think yourselves or anything in the house worth having some kind of protection
  13. al-yeti
    Hardcore What was it then? Ion40 ?
  14. al-yeti
    On a side the galaxy dimension panel wasn't made for the diyer Lack of information is more about lack of knowledge, training and experience So other panels you will find same situation where you don't know what it can and can't do
  15. al-yeti
    Would accept both
  16. al-yeti
    Ok dude I remember the external coms devices and cards
  17. al-yeti
    The versions are upgraded for development and sometimes correcting earlier glitches Version 7 example was superseded within week I think and so on Firmware easy to do , just buy it on a stick or if you can get the files there are other ways
  18. al-yeti
    That's what I thought C for confused dot come in my case lol They both have Comms on board tho
  19. al-yeti
    What about the C and the D?
  20. al-yeti
    Maybe the cable at conservatory has been damaged and now shorting out the supply So if fuse is ok possible panel damaged , but that won't resolve the issue replacing panel if cable still has a problem
  21. al-yeti
    Turn battery on And put on SCB mode
  22. al-yeti
    Where did you get bell? Is bell tamper closed? Does bell have jumpers you can take picture of Actually I see the jumpers
  23. al-yeti
    That's the first move to try make sure your bell is working But wouldn't the bell wait for the tamper to close and he's forgetting that?
  24. al-yeti
    Nothing happens when you do what?
  25. al-yeti
    Bell and strobe would be tied together into the normally open side of the relay , then common relay to 0v , I think lol The tamper you need to for now ground it in the bell if it allows so it ignores it , I think lol
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept