Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,438

  • Joined

  • Last visited

  • Days Won

    129

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    That's the first move to try make sure your bell is working But wouldn't the bell wait for the tamper to close and he's forgetting that?
  2. al-yeti
    Nothing happens when you do what?
  3. al-yeti
    Bell and strobe would be tied together into the normally open side of the relay , then common relay to 0v , I think lol The tamper you need to for now ground it in the bell if it allows so it ignores it , I think lol
  4. al-yeti
    Seems as though you can't programme as above So you need to use 0v +12v Then the relay for the bell trigger , which drops bell trigger to 0v when siren goes The tamper could be used on a zone in defence mode , look at page 11 , although not a tamper it can act as a 24hr armed zone , but you would have to mess around to make it work
  5. al-yeti
    Assuming that zone on the back is programmable it might work , you also have an onboard relay which could be used for a bell trigger depends on what it does
  6. al-yeti
    Unlikely anyone uses that alarm Anymore pictures or a link to the installation manual ?
  7. al-yeti
    No need to justify I fixed one today and added a gsm unit , no bother..... Case design is good , it's you lol
  8. al-yeti
    Common problem on these are the spring , users mess around with the cover and screw and realise it was the spring after all Not surprised by what you're saying you didn't need to do half of what you did but it is how it is, you damage the case Be gentle adjust spring and your done, or call an engineer... ...
  9. al-yeti
    Assume new intercom needs relay?
  10. al-yeti
    Yo Topic thoroughly discussed on trade side, apply and join the alarm gorillas
  11. al-yeti

    Version 1

    14 downloads

    Da abacus programming file
  12. al-yeti
    Da abacus 6 8 View File Da abacus programming file Submitter al-yeti Submitted 29/06/20 Category DA Digital Audio
  13. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    In those days you would get it quite quick aswell
  14. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    Ok , but reality this panel is now an antique and junk to most But great for DIY while it works perhaps
  15. al-yeti
    ?
  16. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    Yeah I get you But there needs adjustment to alarms from certain era lol Surley a.single page showing bell links won't matter Ah forget it lol
  17. al-yeti
    Unlikely You are Asian
  18. al-yeti
    Must be asian
  19. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    Not even for this old thing?
  20. al-yeti
    Enter user code to stop it sounding
  21. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    Model 76 / 77 Those had links for bell delay etc The old da for code changing was the old wire links used to be interesting to
  22. al-yeti

    Acorn Alarm Panel

    al-yeti replied to a topic in Guest Forum

    Acorn might be installer Upload picture of keypad
  23. al-yeti
    In India?
  24. al-yeti
    Not really Is it a jekyll and Hyde thing?
  25. al-yeti
    Y ? You display it somewhere ?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept