9651
-
Posts
2,480 -
Joined
-
Last visited
-
Days Won
5
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Everything posted by 9651
-
we don't have zones set up as omit. If the customer wants it, it's logged
-
Never assume it certainly could be iD
-
Galaxy G2 1.56 Firmware & Dualcom DigiAir
9651 replied to phkennedy's topic in !!..DIY Installers..!!
Madness -
Correct
-
Must be to do with the mesh then, as a galaxy will just report the device as an rf fail when flat
-
Question so when these ricochet devices go flat, why are they jamming? I believe that was my issue and I see it mentioned above a simple point tamper would suffice!
-
I've just had to UDL our "problem site" again. Its been fine for 6 months.... but just taken a call of Alerts displaying. Radio jam is present and wont clear - every sensor jammed out.. Had a couple of low batteries over the last few days according to log, so presume a faulty device jamming the rest. 50+ ricochet zones. Brilliant. Wireless toss.
-
Genie is OK but personally don't like the user interface, bit quirky and looks old fashioned/cheap. Also the same with the cms picture quality of the IP stuff is fine mind, juts seemed to get lots of failures on the gunmetal domes for some reason
-
Id re start it (if you dare) i had had one that kept showing set with General fault, but with no faults present for around 12 months. Power cycle sorted it, but that's if it doesn't crash/not start back up first......
-
Too busy really.........just recently, stupidly so based north west not a bad thing I suppose, but plenty of 12 hr days and what not....
-
We are about to use dahua for all our IP stuff now. We did use genie, but it's too limited for what we need and we have had quite a few faulty cameras..... Currently have a 64 channel on the bench and impressed, twin LAN, twin hdmi etc. Also like the cms software. Jut need to try it monitored but I'm sure it will be fine
-
Is there no alarm on site to mimic cct/ links etc??
-
Yup I fitted one in a pub! In Rhyl lol! What about an accenta ID?! I fitted two, one is still going. Take 8 zones in iD wiring config, but only use biscuits 1-8
-
You could run anything through an optima, all sorts of bells hanging off them. I cut my teeth on optima/Accentas
-
The ultimate could do anything, and could run two lines of iD. The only issue for me was the flakey build quality of the pcb itself. All of our Ultimates have long gone, but as mentioned above still have many K+ nocking about. Any that die or need upgrading go to Texe, either with 60iXD unit, or wireless
-
we used to fit all the range, logic 4 up to Ultimate. Back in the day the Karizma + was a cracking panel, and we still have lots under maint and comms. Looked after and correctly installed, they were/are very stable. Ultimate, hmmmm not as robust imo.
-
You did the polling set up all via the keypad and not via laptop I take it? It makes a note of it in the manual
-
We have a fair bit! Think of one 2500 with a good 70+ biscuits at a guess
-
not too bad then. Not something ive had to do tbh, but handy to know,
-
how messy is that though at the camera end? Ie how big is the converter?
-
not had any issues personally at that distance. Sometimes on a longer run we may supplement it with a .75 flex, but its rare
-
proper cat5e all the way.
-
CCA Basically its ****, and gives a much higher resistance than standard copper cable. Measure the resistance on the runs, you'll be surprised (maybe) We tend to fire the video down a twisted pair (browns), then power down the two others. So thats the blues twisted together, and the oranges.
-
Any modification to the supply side would/should need a minor works.
-
nope You done need to be qualified to be an electrician, just competent. Under the scope of competent, the only way to "prove" you are, would be works done follows 7671. So thats where all the paperwork comes from.