Jump to content
Security Installer Community

grantc

Trade Full Member
 View Profile  See their activity

  • Posts

    67

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by grantc

  1. grantc
    Powering the camera as the Poe port on the back of the NVR doesn't put out enough power?
  2. grantc
    Any him ptz's I've fitted have needed additional power. The camera comes with either a PSU or Poe injector in the box. Grant Hik*
  3. grantc
    Some more junk if you want it? The first 2 boxes are decoys. Dunno if you collect them? There is a keypad inside the gardtec panel - not sure if it works? The old Scanny apparently still works and was regularly maintained. Grant
  4. grantc
    Ok will look them up!
  5. grantc
    Yeah no probs, will get a price when I get a minute. Cheers
  6. grantc
    This too if you want it?
  7. grantc
    Logan.... Ripped this out this morning. Is it of any interest to you? I can post when I get a chance if you cover postage. Grant
  8. grantc
    Pyronix V2 GSM Pretty sure I have one I'd sell if you're interested. Grant
  9. grantc

    Old Car Chat

    grantc replied to MrHappy's topic in Just Joking

    I actually own a MK2 fiesta XR2 funnily enough. Have done for about 13 years. Has sat in the garage most of those
  10. grantc
    Go to assign keypads and readers and check all other addresses apart from 0. I suspect one is programmed as a reader/keypad. Set them to unused. 0 should be a keypad. Come out of engineers mode and that should sort it hopefully. Grant
  11. grantc
    Thanks James. In that case, press and hold D till it says enter security code. Put in 2000. Press no till you get to address and make it 1 Press A to save Keypad should be working.
  12. grantc
    Your working keypad should be address 0. Got to assign keypads and readers and select keypad address 1. Make this a keypad. Then you have to access a hidden menu on the non working keypad and address it as 1 - Admin - ok to give out this info? That should get the 2nd keypad working. The panel has to be powered up on mains first to recognise the Digi WiFi so it shows in the menu.
  13. grantc
    Does it come out of engineer mode? It should tell you the issue if it doesn't. Keypad will have went red as you created a keypad tamper. Won't go green again till it's out of engineer mode/keypad tamper resolved.
  14. grantc
    How old the battery?
  15. grantc
    Delete all serial no.s of RF zones
  16. grantc
    Switch Comms format to not used. You using Digi WiFi for app only? Go through WiFi settings within Comms to connect to router etc
  17. grantc

    Pyronix Cloud

    grantc replied to Al72x's topic in Guest Forum

    Re install the app? Has your subscription ended?
  18. grantc
    Fair enough, sounds like a nightmare.... Did it happen last thing on a Friday by any chance? :-)
  19. grantc
    Can't you view zone types/descriptions in menu 21 take note then bite the bullet and default?
  20. grantc
    Free subscription came to an end?
  21. grantc
    Why are you using 2 buttons to unset b? The unlock button should be setup for unset any
  22. grantc
    2 boards on them. Bell wired off the small PCB at bottom. Wire tamper across on of the onboard zones and program accordingly.
  23. grantc
    Post a pic of the actual tag your using
  24. grantc
    I'll ask the obvious, are you holding the tag up to the top right of the screen? When you add a user, it says enter code then you present tag. Is that what you are doing?
  25. grantc
    The pic looks like the correct tags. Does it beep when you hold the tag up?
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept