Timmymeads

Okay I put in code and then present night set and it has a delayed silent alarm so I think I need to program in the sound?

Peter - How do I enable night set - I’ve tried #+3 and get 3 beeps - Pretty sure one programmer it aswell and nothing?

Hi Peter, There was no wires originally in 5.6.7 so I linked them in. When I do a easy set it gives me a different sound like the one when I omitted the zones manually. It does 10 second count down and then it sets. I stayed in the house and walked to a detector and the main alarm sounded so think all should be fine. I’ll try the other detectors too

Thanks for your help Peter - I’ve done it and it all works like it should! nice one mate

Ah I see just 2 wires between 3 zones - then the wires I took out originally just cut them back and insulation tape?

Shall I take our 5.6.7 zones only and join them together and cap them only. Then try alarm ?

If I link out 5.6.7 zones then if I use easy set will it arm?

Yes I can link out and no how to do it just need to figure which wire is for which.l, I don’t have a multi meter but there might be instructions. I was more if I could do it through the panel system

I have the programming code - How do it do it?

I have to omit the zones each time to set the alarm by User code + 6 then press 5,6,7 * then press easy set #+1 then this set the alarm. It will set alarm off if the PIR is obstructed. But once I do this or open door and enter the code. I have to manually do this process again! Any support would be appreciative.

Must be a logical explanation

It’s works fine for me - Why pay out when I have a functional alarm just with a few teething issues - Can anyone figure out? I must have done a master reset somehow although I didn’t ommit 5,6,7

yes tried opening and shutting the door and also tried making it so the exit beep is 10 seconds and nothing changes?! So frustrating

Hi Logan, swwo I know engineer code and a user code when I put both codes in the alarm sets, PIR 5/6/7 are all red lit and day button is flashing green and power green. But it just continues to beep and not set? any ideas? 60415630111__75584551-E5B4-4D01-A726-9B8D01A418B8.MOV

I don’t think people really can be bothered with what you have stated. Instead you have just wanted to be differcult... and proven unhelpful - Take your power elsewhere Logan - and remember with great ‘power, comes..... not!

These manuals are searchable by anyone on the World Wide Web. Why the issue? If you don’t have anything supportive to say please don’t contribute anything. Off topic: Yes as everyone who was supporting went off topic

Hi, I revived my ADEMCO ACCORD 8 system with a fuse as must have blown it when disconnected key pad some time ago. Everything seems to work fine. The x3 PIR flash red on movement. The key pad is powered and I know the engineer code and user code. Although when I enter user code + 1 it starts to beep then doesn’t stop. The zones 5,6,7 are red and omitted I believe. Not sure if I did a factory reset. When bringing the system back to life. I have the manual ....

Not sure... what u mean - I just wanted it to work

I know the engineer code now and master code - Do I have to program my zones? How do I enter programming mode

Lol.. thanks mate I’ve got the manual also but doesn’t mention anything about that

60295166198__516C6098-1914-44CC-B644-F28D22AAB618.MOV 60295171866__6A513E9D-1312-4C8E-99A0-754882D70C59.MOV

I did #### (8) (1) then (my code) so when I use #### now it does nothing but when I use (my code) + 1 (full set) it just beeps and doesn’t stop. I open and shut the door too

I just tried new code and Set alarm it just continues to beep and doesn’t stop?

Hey guys managed to reset it and now I know my code - Tested the sounder and fine - I don’t know how to east set apparently it’s #+1 but this just gives me x2 beeps. Am I right in thing when I enter code and press 1 (Full set) the zones that are red on the panel are not active? Which would make sense to my numbers location alarms that aren’t l?

Can I do a master reset by cutting electric/opening the mains box. Make the tamper pressed down with tape (as if the box is shut onnit) then mains on, disconnect x1 battery positive wire. Then mains off. Then mains on again and connect battery then run to panel and hold * & # together . Apparently that puts it in reset? It will then flash up the master number sequence ? Does that sound right?