allenp Posted April 26, 2008 Share Posted April 26, 2008 can anyone assist? I have an old Omnicrom 7000 control panel fitted, and though that I would replace the bell box with a Pyronix Belle box. Can anyone help with the wiring? Any advice would be excellent. Omnicrom panal wiring: bell - black bell + blue Str + green Str - yellow Scb red RTO white Pyronix Bell Box connections B- B+ BA STB Spare BT BF Could smoeone tell me which wires go where? thx Link to comment Share on other sites More sharing options...
antinode Posted April 26, 2008 Share Posted April 26, 2008 B- Red B+ Blue BA Black STB Yellow Spare BT White BF Link this terminal to "B-" in the bell box Disconnect the Green at the control panel end, or put it in the Spare terminal in the bell. Trade Member Link to comment Share on other sites More sharing options...
allenp Posted April 28, 2008 Author Share Posted April 28, 2008 B- RedB+ Blue BA Black STB Yellow Spare BT White BF Link this terminal to "B-" in the bell box Disconnect the Green at the control panel end, or put it in the Spare terminal in the bell. antinode, many thanks for your help and excellent advice, the Pyronix bell box works fine now. Allen Link to comment Share on other sites More sharing options...
lawandorder Posted April 28, 2008 Share Posted April 28, 2008 antinode,many thanks for your help and excellent advice, the Pyronix bell box works fine now. Allen My advice would be: 1 Disconnect mains and test for safe isolation. 2 Disconnect the battery. 3 Disconnect all the wires from the control panel. 4 Remove the screws which affix the panel to the wall. 5 Place panel in a suitable waste disposal container. Only joking mate, glad you got it sorted. Link to comment Share on other sites More sharing options...
kka Posted April 28, 2008 Share Posted April 28, 2008 we can all knock them , but i was at one the other day that was over 15 years old, and still going strong.... Kevin Scott. Owner of KK Alarms...... Installation .. Service .. Repair ...... Thoughout.. Northumberland and North Tyneside ..... Tel:01670 361948 (call diverted after 15 seconds) or 07947444114 Link to comment Share on other sites More sharing options...
lawandorder Posted April 28, 2008 Share Posted April 28, 2008 we can all knock them , but i was at one the other day that was over 15 years old, and still going strong.... Very true, a lot of people don't like Texecom but for small domestics I think they are fine. I think I was put off by the fact that mosty of the Omnicrons I ever worked on were DIY Wickes kits and hadn't been fitted to a very good standard in the first place. The oldest panel still under contract would make an interesting topic I reckon. Does anyone remember A&G R4 and R4E? Link to comment Share on other sites More sharing options...
Guest anguscanplay Posted April 28, 2008 Share Posted April 28, 2008 this is my current eldest Link to comment Share on other sites More sharing options...
Alarm Protection Posted April 28, 2008 Share Posted April 28, 2008 We have 6 A&G Diplomats still under service and im sure the oldest one is 17 years old. Still going strong but need upgrading!! ! Link to comment Share on other sites More sharing options...
antinode Posted April 28, 2008 Share Posted April 28, 2008 Worked on loads of old Bently panels like the Symphony, F133 and the big cream one with about 16 zones on it. All still going strong 20 years after they were installed, some on the original detectors aswell! Trade Member Link to comment Share on other sites More sharing options...
Guest anguscanplay Posted April 28, 2008 Share Posted April 28, 2008 We have 6 A&G Diplomats still under service and im sure the oldest one is 17 years old.Still going strong but need upgrading!! 17 years pah - the one in the photo was fitted over 25 years ago now 17 years is 9600 and 9800 teritory (?) mere youngsters LOL Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.