AlarmDoctorBrigg Posted December 18, 2016 Share Posted December 18, 2016 (edited) Hi all, Im just programming up a some texecom 48-w kit2's for jobs this week and one of the panels has no response from the tx/rx LED's on the onboard exp1 side of the board and nothing from the wireless signal LED's either. also in confirm devices this isn't being seen by the panel? do you think I've fell unlucky and got a faulty panel? thanks in advance 50378603619__046443B7-DADF-4BB8-A47D-0E89A642FFD7.MOV Edited December 18, 2016 by AlarmDoctorBrigg Quote Link to comment Share on other sites More sharing options...
PSE Posted December 18, 2016 Share Posted December 18, 2016 If you've got no TX /RX LED's then the Panel processor has gone This will also occur if you plug on a RM8 relay module without powering the panel down. It blows the panel Quote Link to comment Share on other sites More sharing options...
sixwheeledbeast Posted December 18, 2016 Share Posted December 18, 2016 Not necessarily there maybe a short on the data Quote Link to comment Share on other sites More sharing options...
AlarmDoctorBrigg Posted December 18, 2016 Author Share Posted December 18, 2016 1 minute ago, sixwheeledbeast said: Not necessarily there maybe a short on the data This is being done with the keypad on a fly lead (no other wires connected to the panel) except mains to power it for programming purposes as learning the ricochet devices and programming the part sets up. the other 3 kits I had to do have been programmed and reboxed ready for installing. just this one kit when powered up has no LED's lit on the right hand side of the board like the other 3 kits did. even after defaulting the nvm and clean starting. no shorts on the data on my engineer keypad I use it daily! the wireless expander is onboard on the 48W and is not even seen in the expander menu and not seen when confirming devices (only the connected keypad) Quote Link to comment Share on other sites More sharing options...
sixwheeledbeast Posted December 18, 2016 Share Posted December 18, 2016 Sorry yes, I just noticed it's a 48-W. You mean the LED's near the flashing port? Quote Link to comment Share on other sites More sharing options...
AlarmDoctorBrigg Posted December 18, 2016 Author Share Posted December 18, 2016 Yes near the ricochet firmware flashport and the tx rx below neither are flashing? The tx rx on the left side of the board ok though Quote Link to comment Share on other sites More sharing options...
sixwheeledbeast Posted December 18, 2016 Share Posted December 18, 2016 If you have proved your engineers keypad and lead is ok and the DIP switches to enable the radio side are on then I can't think of anything else. Quote Link to comment Share on other sites More sharing options...
AlarmDoctorBrigg Posted December 18, 2016 Author Share Posted December 18, 2016 To be honest I think I've just been unlucky with this one. ive never had an issue in the past, just power up on mains, program and rebox them for install. this is the first time I've had one not respond. With it being all one pcb aswell, unless faulty there should be no reason for the LED's not to power up out of the box. Quote Link to comment Share on other sites More sharing options...
al-yeti Posted December 18, 2016 Share Posted December 18, 2016 So you checked switches ? Ebay purchase? Quote Link to comment Share on other sites More sharing options...
AlarmDoctorBrigg Posted December 18, 2016 Author Share Posted December 18, 2016 Lmfao eBay purchase, No i only purchase off security warehouse All the switches all on (as was the other kit I've just programmed - it's the kit002 all out the box setup from Texecom, link on commission mode for ricochet device learning (I've been using Texecom equipment for last 12 years) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.