Gabs Posted February 11, 2017 Posted February 11, 2017 Does anyone have an ADE Opus 42 printer taht they don't want? I need one for my Accenta Mercury. I'd pay postage Quote
datadiffusion Posted February 11, 2017 Posted February 11, 2017 Depends, vapourware or just a rebadged Casio etc...? Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands
Gabs Posted February 11, 2017 Author Posted February 11, 2017 5 minutes ago, datadiffusion said: Depends, vapourware or just a rebadged Casio etc...? Hmmm, I don't know. Whatever works with it? Do you have a compatible printer? I don't mind any brand Quote
datadiffusion Posted February 11, 2017 Posted February 11, 2017 No binned my 9500 etc.. printers a while back. Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands
MrHappy Posted February 11, 2017 Posted February 11, 2017 I've never seen an opus 42 or cpa6 I acquired datac printer from scantronic multiscan, In my experience a branch of national co. or large regional installer might have one 7300 nvm programmer or a logging printer Quote Mr Veritas God
Gabs Posted February 11, 2017 Author Posted February 11, 2017 3 minutes ago, datadiffusion said: No binned my 9500 etc.. printers a while back. Shame, I can't seem to find anything like it on eBay, it only requires 3 wires to connect to the panel. 2 minutes ago, MrHappy said: I've never seen an opus 42 or cpa6 I acquired datac printer from scantronic multiscan, In my experience a branch of national co. or large regional installer might have one 7300 nvm programmer or a logging printer Do you know if anything like these are still made, for panels like the Galaxy?? Quote
datadiffusion Posted February 11, 2017 Posted February 11, 2017 When I took out a Menvier panel a few years back, there was a till roll inside where back in 1996 the original Co. had printed out the programming data, just in case I suppose! Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands
MrHappy Posted February 11, 2017 Posted February 11, 2017 most panel manufacturer list printer interfaces, bet they sell less than they are churches saudi I think this is the same as my datac printer? https://www.checkline.eu/products/126322/large/126322.jpg Quote Mr Veritas God
Gabs Posted February 11, 2017 Author Posted February 11, 2017 1 hour ago, datadiffusion said: When I took out a Menvier panel a few years back, there was a till roll inside where back in 1996 the original Co. had printed out the programming data, just in case I suppose! 1 hour ago, MrHappy said: most panel manufacturer list printer interfaces, bet they sell less than they are churches saudi I think this is the same as my datac printer? https://www.checkline.eu/products/126322/large/126322.jpg Thanks for the reply, guys This may be a bit off topic from this, but have you taken out any dead panels? Like an Optima, Accenta or something simple like that? I want to pull apart an alarm circuit board, to see in detail how it works, and how it has been programmed. I also need a casing for my Accenta Mercury panel, any help is much appreciated Quote
al-yeti Posted February 11, 2017 Posted February 11, 2017 35 minutes ago, Gabs said: Thanks for the reply, guys This may be a bit off topic from this, but have you taken out any dead panels? Like an Optima, Accenta or something simple like that? I want to pull apart an alarm circuit board, to see in detail how it works, and how it has been programmed. I also need a casing for my Accenta Mercury panel, any help is much appreciated Are used ones not cheap on eBay? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.