paulbaker1954 Posted September 27, 2020 Share Posted September 27, 2020 Got a Gardtec 595 panel linked to the Risco wireless module. Two of the wireless shock sensors are triggering false tamper alarms and is now occurring at least twice a day. Have tried changing the sensor battery but still the same. Any othe ideas to fix? Alternatively I could just get rid of them but I can’t figure out how to unconnected them from the wireless receiver, anyone know how this is done. I tried simply taking batteries out but that didn’t help Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 adjust spring (s) / the case is damaged to remove from system you need to program the circuits off Quote Mr Veritas God Link to comment Share on other sites More sharing options...
Hillbilly Posted September 27, 2020 Share Posted September 27, 2020 Like all risco tat over time issues like this appear for no reason at all.I had this and had to replace them. Had this issue with a wireless door contact last week randomly tampering and replaced it. It is only in contacts that has been the tamper issue over time. Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 27, 2020 Share Posted September 27, 2020 2 hours ago, Hillbilly said: Like all risco tat over time issues like this appear for no reason at all.I had this and had to replace them. Had this issue with a wireless door contact last week randomly tampering and replaced it. It is only in contacts that has been the tamper issue over time. Well many systems got the querks , I got my first hkc wirreess contact where the reed inside sticks , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is Risko have these problems long time now Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 26 minutes ago, al-yeti said: Well many systems got the querks , I got my first hkc wirreess contact where the reed inside sticks , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is Risko have these problems long time now The one way radio devices are rock solid Gardtec controls are quirky, but workable Wisdom / Agility, my life is too short... Quote Mr Veritas God Link to comment Share on other sites More sharing options...
aissecur Posted September 27, 2020 Share Posted September 27, 2020 As per previous comment, adjust the spring & ensure the battery is at a healthy level some sit on a spacer, so make sure that’s not causing any issues Or that the spring is not bent (has that before) if you want to remove from the zone you need the engineer code & it’s done on the program zones (first option when in engineers mode) Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 27, 2020 Share Posted September 27, 2020 2 hours ago, MrHappy said: The one way radio devices are rock solid Gardtec controls are quirky, but workable Wisdom / Agility, my life is too short... Wisdom hardcore messed up , although I sold a few brand new boxed that someone gave up on Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 36 minutes ago, aissecur said: As per previous comment, buy a dog ? Quote Mr Veritas God Link to comment Share on other sites More sharing options...
james.wilson Posted September 27, 2020 Share Posted September 27, 2020 Does anyone rate risco anymore? I know the past and how it was 1 way would you use it out vs anything else? Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 28, 2020 Author Share Posted September 28, 2020 (edited) Thanks all for comments. If I can’t fix them and get new senders I have the install manual for the senders that says set the receiver to write mode but I don’t know how do this. The receiver is a separate square white box wired in to the gardtec panel. if anyone has the install instructions for the receiver they can share that would be fab Edited September 29, 2020 by MrHappy removed Risco's file Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.