How do I get this to work?

[Henrik]

I will attach a short movie on what the display says and a pic on how it looked before I took the old cables away.

I put the 1k resistor between 1002 and 0V to the left of 1002.

On the film it says (in Swedish):

1003 +SAB.Open circuit IR store floor

1002 +SAB.Short circuit IR store office

 

Not beging an alarm technician guy I just guess that 1001 (that's a door magnet) would have 1=white and 0V=Blue and the 1002 that's an PIR would be connected with 2=purple 0V=green and blue and then the white to 12V on pin 7.

[al-yeti]

9 minutes ago, Henrik said:

I will attach a short movie on what the display says and a pic on how it looked before I took the old cables away.

I put the 1k resistor between 1002 and 0V to the left of 1002.

On the film it says (in Swedish):

1003 +SAB.Open circuit IR store floor

1002 +SAB.Short circuit IR store office

 

Not beging an alarm technician guy I just guess that 1001 (that's a door magnet) would have 1=white and 0V=Blue and the 1002 that's an PIR would be connected with 2=purple 0V=green and blue and then the white to 12V on pin 7.

IMG_1265.MOV

Going to basics 

 

If your remove the wiring and put a resistor in the correct place it should clear any fault that is present there 

[al-yeti]

In your picture above zone 3 shows the wiring sheath isn't removed and can be a problem , did you correct that?

[al-yeti]

On 28/10/2020 at 18:10, Henrik said:

Ok guys, got everything up and running just fine.

i do however have an slight issue.

when I took the alarm down I most have missed one PIR hanging on the wall (address 1002).

how do I go about entering the engineer code to be able to delete the address 1002?
And is the engineering code always the same or is it changeable by the company who first installed the system in my old shop?

thanks in advance,

 

Henrik.

Another thing , show a picture of how one of your pirs is working , how is it wired and what resistors are inside it 

 

This will help you why your not able to clear the fault on z2& z3

[Henrik]

2 minutes ago, al-yeti said:

In your picture above zone 3 shows the wiring sheath isn't removed and can be a problem , did you correct that?

the picture above is the old wiring, and the film showing the new. Where would I place the resistor then to place it in the right place. :0)

[Henrik]

Here is a pic how I wired PIR 1003 up.

Blue= Ground,

Orange= 12V

Brown= alarm

Green= tamper

 

[al-yeti]

24 minutes ago, Henrik said:

Here is a pic how I wired PIR 1003 up.

Blue= Ground,

Orange= 12V

Brown= alarm

Green= tamper

 

What values are the resistors? As you used the tamper one to put on the panel

 

 

All I am saying if you can't clear the fault with a simple resistance, then your eol must be set different to what your putting in and it doesn't matter what sensor or cable your using , all of no consequence 

 

What happens if you move a sensor from further up to zone two or three , it should clear the fault and send the fault to other Rio output 

[Henrik]

The resistors are Brown.brown.black.black.brown

110 ohms +/- 1%
 

moved 1003 to 4 and 1004 to 3 and that cleared the problem on +SAB 1003.

still got the problem on 1002 that supposed to be a PIR but still sits on the wall in my old shop.

[al-yeti]

Just now, Henrik said:

The resistors are Brown.brown.black.black.brown

110 ohms +/- 1%
 

moved 1003 to 4 and 1004 to 3 and that cleared the problem on +SAB 1003.

still got the problem on 1002 that supposed to be a PIR but still sits on the wall in my old shop.

Can't be 110 needs to be 1k I thought 

 

Unless your saying all the zones set up that way 

[Henrik]

Sorry mate, it’s brown black black brown brown 1k +/-1%