Help me to connect my external detector to my CPU board

[Hack]

Hi everyone,

 

Please help me to know how to connect my volumetric motion detector (Pyronix XD10TT-AM) to my ELKRON MEDEA32 board.

The detector includes pre-installed resistors to be activated by a connection as needed (see the shared assembly).

 

Schema of the assembly of my Pyronix XD10TT-AM

 

In my MEDEA32 board, i have 6 N/C inputs.

Manual of MEDEA32

(page 24 and 25)

I have also a wired add-on Elkron EP708 expansion with 8 points PGM input/output (PrIO).

Manual of EP708

 

1) According to the assembly diagram, should I use programmed input (PGM) or the simple N/C input can be used ?

 

2) Which point on my MEDEA32 board that corresponds to the input (COM) on the assembly of my pyronix.

Some board have zone with a groupe of "AT input / EOL and COM". But this is not the case in my MEDEA32 or the EP708 add-on.

Here is an exemple of PCX46 (Pyronix)

 

Thanks a lot

 

Edited July 27 by Hack
orthograph

[al-yeti]

20 minutes ago, Hack said:

Hi everyone,

 

Please help me to know how to connect my volumetric motion detector (Pyronix XD10TT-AM) to my ELKRON MEDEA32 board.

The detector includes pre-installed resistors to be activated by a connection as needed (see the shared assembly).

 

Schema of the assembly of my Pyronix XD10TT-AM

 

In my MEDEA32 board, i have 6 N/C inputs.

Manual of MEDEA32

(page 24 and 25)

I have also a wired add-on Elkron EP708 expansion with 8 points PGM input/output (PrIO).

Manual of EP708

 

1) According to the assembly diagram, should I use programmed input (PGM) or the simple N/C input can be used ?

 

2) Which point on my MEDEA32 board that corresponds to the input (COM) on the assembly of my pyronix.

Some board have zone with a groupe of "AT input / EOL and COM". But this is not the case in my MEDEA32 or the EP708 add-on.

Here is an exemple of PCX46 (Pyronix)

 

Thanks a lot

 

So your just using the AA and TT terminals in that case without eol and without any resistors 

[Hack]

1 hour ago, al-yeti said:

So your just using the AA and TT terminals in that case without eol and without any resistors 

 

thaks al-yeti 

I understand that without resistor is functionnal like you said.

But the constructor recommand the use of two transistor to avoid false alarms and short circuits.

I just need to know the equivalent of (COM) in my MEDEA32 board or the add-on EP708. 

Edited July 27 by Hack

[al-yeti]

28 minutes ago, Hack said:

 

thaks al-yeti 

I understand that without resistor is functionnal like you said.

But the constructor recommand the use of two transistor to avoid false alarms and short circuits.

I just need to know the equivalent of (COM) in my MEDEA32 board or the add-on EP708. 

Lol

 

I tried to look at manual it's as bad as other manuals

[MrHappy]

Just now, al-yeti said:

I tried to look at manual it's as bad as other manuals

 

some odd ball euro thing -

 

https://www.elkron.it/prodotti/scheda-elettronica-medea-32/?lang=en

 

 

[Hack]

To have a look on the Pyronix XD10TT-AM assembly

https://www.atexshop.com/download/pdf/XD10TTAM 10m External Detector.pdf

Edited July 28 by Hack

[al-yeti]

1 hour ago, Hack said:

To have a look on the Pyronix XD10TT-AM assembly

https://www.atexshop.com/download/pdf/XD10TTAM 10m External Detector.pdf

This is easy bit lol 

[Hack]

Thanks a lot Al yeti 

I can't use the pre installed resistors in my Pyronix XD10TT because my board ELKRON recommand others (5,11-10 and 15kOhm)

Then, i must install them manually like this 

[al-yeti]

1 hour ago, Hack said:

Thanks a lot Al yeti 

I can't use the pre installed resistors in my Pyronix XD10TT because my board ELKRON recommand others (5,11-10 and 15kOhm)

Then, i must install them manually like this 

Ok but you don't have to use the fault